朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

Simulation and energy optimization of the stabilizer tower of a pyrolysis gasoline hydrogenation unit

Energy optimization of second distillation tower of a pyrolysis gasoline hydrogenation unit has been studied by the thermal cycle of vapor recompression method. The mentioned cycle is connected to the second distillation tower of the stabilizer of pyrolysis gasoline, and the results are found promising. The composite pinch curve for both the current and the optimized methods are shown. Moreover, an increase in the heat transfer rate in heat exchanger E-1014 causes energy recovery in reboiler. According to simulation results, by vapor recompression to 1970 kPa and using this heat source for thermal integration, condenser and reboiler’s energies are decreased by 56.93 and 30.4 percentage, respectively.     

An up to date review of continuously variable speed wind turbines with mechatronic variable transmissions

As a promising and potential alternative to conventional fixed or variable speed wind turbines, continuously variable speed wind turbines (CVSWTs) with variable transmissions offer improved power efficiency and enhanced power control capabilities. The CVSWTs can be generally achieved by adapting mechatronic variable transmissions in the turbine drive train for continuously variable speed operations for wind turbines. Therefore, this paper serves to provide an up to date and exhaustive review of the CVSWTs with mechatronic variable transmissions such as mechanical variable transmission, electrical variable transmission, and power splitting transmission. In this paper, the analysis of CVSWTs with different mechatronic transmission topologies is performed regarding basic configurations, dynamic characteristics, control principles, and experimental or simulation results. Review results indicate the feasibility of applying CVSWTs with such mechatronic transmissions and highlight superiorities of the CVSWTs with power splitting transmission. The CVSWT with power splitting transmission will be particularly suitable for megawatt‐scale turbine systems and will hence increase the economic competitiveness of these turbines due to its large power capacity and high reliability. The directions or challenges for future investigations of CVSWTs with such mechatronic transmissions are also presented to foster in‐depth understanding of such CVSWTs and their control strategies.     

Design and optimization of radioisotope sources for betavoltaic batteries

A Monte Carlo source model using PENELOPE was developed to investigate different tritiated metals in order to design a better radioisotope source for betavoltaic batteries. The source model takes into account the self‐absorption of beta particles in the source which is a major factor for an efficient source design. The average beta energy, beta flux, source power output, and source efficiency were estimated for various source thicknesses. The simulated results for titanium tritide with 0° and 90° angular distributions of beta particles were validated with experimental results. The importance of the backscattering effect due to isotropic particle emission was analyzed. The results showed that the normalized average beta energy increases with the source thickness, and it reaches peak energy depending on the density and the specific activity of the source. The beta flux and power output also increase with increasing source thickness. However, the incremental increase in beta flux and power output becomes minimal for higher thicknesses, as the source efficiency decreases significantly at higher thicknesses due to the self‐absorption effect. Thus, a saturation threshold is reached. A low‐density source material such as beryllium tritide provided a higher power output with higher efficiency. A maximum power output of approximately 4 mW/cm³ was obtained for beryllium tritide with SiC. A form factor approach was used to estimate the optimum source thickness. The optimum source thickness was found near the thickness where the peak beta particle average energy occurs.     

单一低渗透突出煤层水力冲孔工艺优化应用分析

为了有效提高单一低渗透突出煤层的瓦斯抽采效率，以高压水射流冲击理论为指导，针对平煤股份八矿己组突出煤层特征建立数值模型，模拟分析水力冲孔应力分布规律，通过现场实测分析冲孔有效影响范围，进一步优化设计冲孔参数、指导现场施工。现场应用表明，水力冲孔是一种行之有效的方法，对单一低渗透突出煤层实施水力冲孔卸压增透、提高瓦斯抽采效果具有重要意义。     

The influence of the waveguide on the quality of measurements with ultrasonic Doppler velocimetry

The article is devoted to the study of the influence of geometric parameters of sound-conducting walls on the quality of measurement of liquid metal flow velocities by ultrasonic Doppler velocimetry. It was shown that the thickness and radius of a sound-conducting wall (waveguide) have a notable effect on the resulting velocity profiles. The flow in a round pipe, the length of which is much larger than its diameter, is considered as a reference flow. The positive effect of a stepwise waveguides with a diameter smaller than the diameter of the piezoelectric element of an ultrasonic transducer on the quality of velocity measurements was verified experimentally. It was found that the accuracy of the resulting velocity profiles largely depends on the length and the material of the waveguides, as well as the velocity of the incoming flow of liquid metal.     

水泵水轮机导叶动态水力矩特性分析

采用SST k-ω湍流模型对某高水头水泵水轮机进行全流道三维非定常数值模拟,分别对在水轮机工况和水泵工况运行下的导叶动态力矩特性进行分析。结果表明:在水轮机工况下,随着流量的增大,不同位置处导叶的动态水力矩变化规律一致,力矩值由正值变为负值,力矩脉动频率与转轮叶片数相关,流量越大,叶频影响越显著;在水泵工况下,最高扬程工况时导叶水力矩脉动频率主频为转频且脉动幅值较大,而最低扬程工况下导叶水力矩脉动主频为叶频,力矩脉动幅值较小。     

天然气新型气液分离器性能试验研究

为了解决天然气含有饱和水汽和少量烃降低输气效率、堵塞管线和设备等问题,利用旋风子、稳流元件、叶栅式分离元件、折流板式分离元件组合成新型天然气分离器。利用相位多普勒粒子分析仪对新型天然气分离器进出口粒子粒径与液态水含量的进行对比测试,以研究新型分离器的分离效率。结果表明:新型分离器具有良好的气液分离作用;在流量为10～64 m~3/h时,分离器的分离效率成抛物线形式,在33 m~3/h时分离器的分离效率降到最低值95.16%,主要原因是流量在33 m~3/h时,试验气液混合不均匀,导致内部流态紊乱,以至于试验测得分离效率相对偏低;在流量为10 m~3/h时分离器分离效率最高,为99.29%;分离器对该进口条件的气体中雾状液粒有较高的分离作用,且可以明显降低分离器出口气体中液粒的平均粒径;从进口到气相出口压力逐渐降低,总压降为950 Pa;流动区域速度梯度大不利于气液相分离,流动掺混会导致分离效率降低。     

锅炉二次风道流动特性的模拟优化

以武汉武锅能源工程有限公司设计的二次风道为对象,运用数值模拟的方法考查了改造前后二次风道各出口空气的速度分布和质量流量分配情况。结果表明,通过布置弧形挡板,风道出口速度的均匀性显著提升,最大变异系数Cv由29%下降到9%,而且还避免了因风速不均引起的烧边现象。此外,改进后风道各出口空气的流量分配非常接近理想工况,与理想工况的偏差从9.9%缩小到2.1%。